The Tesla Model S Plaid bolt pattern is 5x120, meaning five lug holes on a 120 mm circle. The hub center bore is 64.1 mm, and the lug nuts are M14 x 1.5, torqued to 129 lb-ft (175 N·m) per Tesla's Model S owner's manual. Any aftermarket wheel for a Plaid has to match the bolt pattern, and it should either be bored to 64.1 mm or use hub-centric rings. Shop wheels already sized for the car in our Tesla Model S Plaid collection.
What is the Tesla Model S Plaid bolt pattern?
The Tesla Model S Plaid uses a 5x120 bolt pattern. The "5" is the number of lug studs, and the "120" is the diameter of the circle those studs sit on, in millimeters (about 4.72 inches). Published fitment data lists the same 5x120 pattern across Model S model years, Plaid included, so the Plaid does not need a special pattern compared with other Model S trims. For a deeper walkthrough of how patterns are measured, see our guide to bolt patterns and PCD.
Watch out for look-alikes. The Model 3 and Model Y use a different 5x114.3 pattern, so their wheels will not bolt onto a Model S. Many BMW models also use 5x120, but their hubs are around 72.6 mm, so a BMW wheel will not center properly on a Tesla hub even though the studs line up.
What is the center bore on a Model S Plaid?
The Model S Plaid hub center bore is 64.1 mm. The center bore is the hole in the middle of the wheel that slips over the hub. A wheel with exactly a 64.1 mm bore is hub-centric, meaning the hub carries the wheel's weight and keeps it centered. A wheel with a larger bore can still fit if you add hub-centric rings, which are spacers with a 64.1 mm inner diameter and an outer diameter that matches the wheel's bore. A wheel with a smaller bore will not fit over the hub at all.
Centering matters because lug nuts alone are not a precision locating device. A wheel that sits slightly off-center can cause a vibration at highway speed. Our article on center bore and hub-centric rings covers the details.
What lug nuts and torque does a Model S Plaid use?
The Model S Plaid uses M14 x 1.5 lug nuts (14 mm diameter, 1.5 mm thread pitch), commonly installed with a 21 mm hex socket. Tesla's owner's manual lists 129 lb-ft (175 N·m) with a 21 mm socket. If the wheel maker gives a different figure or requires a specific lug nut for its wheel, follow the wheel maker.
- Thread every lug nut on by hand first to avoid cross-threading.
- Snug the nuts in a star (criss-cross) pattern with the car's weight on the ground.
- Torque to spec with a calibrated torque wrench, again in a star pattern.
- Re-check the torque after a short drive, often 50 to 100 miles, because new wheels can settle slightly.
Avoid running nuts down with a full-power impact gun, since over-torquing can stretch studs. See how much to torque aftermarket wheels and whether you need special lug nuts for more.
Model S Plaid wheel fitment specs at a glance
| Spec | Value | Why it matters |
|---|---|---|
| Bolt pattern | 5x120 | The wheel must have the same stud count and circle diameter. |
| Center bore | 64.1 mm | Wheel bore must be 64.1 mm or larger, with hub-centric rings if larger. |
| Lug nut thread | M14 x 1.5 | Nuts must match the thread and the seat of the wheel. |
| Lug nut torque | 129 lb-ft (about 175 N·m) | Under-torquing risks loosening, and over-torquing can damage studs. |
| Socket size | 21 mm hex | Common size for the factory-style nuts. |
Does the bolt pattern change between 19, 20, and 21 inch Plaid wheels?
No. The bolt pattern, center bore, and lug thread belong to the hub, so they stay the same whether you run 19, 20, or 21 inch wheels. What changes with wheel size is the width, offset, tire size, and ride. Our guide to how wheel size affects Plaid range covers those trade-offs.
What else should you check besides the bolt pattern?
A matching bolt pattern only means the wheel can bolt on. Before you buy, also confirm:
- Offset and width: these decide whether the wheel clears the suspension and fenders. See our offset explainer.
- Brake clearance: Tesla says its carbon-ceramic brake kit for the Plaid doesn't fit its own 19-inch wheels, so tell our fitment experts if your car has it.
- TPMS: your tire pressure sensors need to transfer or be replaced. We sell TPMS sensors if you need them.
- Load rating: the wheel must be rated for the car's weight. Read more on wheel load ratings.
If you want to skip the guesswork, our Tesla Model S Plaid collection lists EVO forged monoblocks, one of our lines, in 19x8.5 / 19x10, 20x9 / 20x10, and 20x10 / 20x11. EX2 (EX2 collection) and three-piece builds such as Corsa and Strada are specced per car, so their sizes can differ, and EVO Custom builds 17 to 24 inch for sizes we don't list. Tell our fitment experts your Plaid's year and brake setup, and we'll spec the fitment. Not sure what to pick first? Start with the best wheels for the Tesla Model S Plaid.
Frequently asked questions
What is the bolt pattern on a Tesla Model S Plaid?
The Tesla Model S Plaid has a 5x120 bolt pattern: five lug holes on a 120 mm (about 4.72 inch) circle.
What is the center bore on a Tesla Model S Plaid?
The center bore is 64.1 mm. Aftermarket wheels should be bored to 64.1 mm, or they need hub-centric rings that bring a larger bore down to 64.1 mm.
What torque do Model S Plaid lug nuts need?
Tesla's owner's manual lists 129 lb-ft (175 N·m) on M14 x 1.5 lug nuts. Use a torque wrench in a star pattern, and follow the wheel maker if it gives a different figure for its hardware.
Can I put Tesla Model 3 or Model Y wheels on a Model S Plaid?
No. The Model 3 and Model Y use a 5x114.3 bolt pattern, while the Model S Plaid uses 5x120, so the wheels will not bolt on correctly.
Is the Plaid bolt pattern different from other Model S trims?
Published fitment data lists the same 5x120 pattern and 64.1 mm center bore across Model S trims, so the Plaid does not need a different pattern. Width, offset, and brake clearance are what vary.
Written by Taylor Smith, co-founder of Variant Alloy Wheels, who has spent nearly two decades in the automotive aftermarket.



Share:
What Is the Corvette C8 Bolt Pattern, Center Bore, and Lug Nut Torque?
How Do You Measure Your Car for New Wheels? Clearance Checks Before You Order