Every Audi R8 uses a 5x112 bolt pattern, and the factory 19-inch setup is 19x8.5 ET42 up front and 19x11 ET50 in the rear. The big trap is the rear hub: first-generation R8s (2008 to 2015) use a 57.1 mm hub at all four corners, while second-generation cars (roughly 2017 to 2023) keep the 57.1 mm front hub but use a larger 66.6 mm rear hub, so a rear wheel made for a first-generation car will not fit a second-generation one.
If you are shopping for Audi R8 wheels, the fitment data is simple once you know which generation you own. This guide covers the factory specs, what changed between generations, and how to choose a width and offset that sits flush without rubbing. Variant builds separate fitments for each generation in the Audi R8 collection, and if you're not sure which car you have, tell our fitment experts your year and trim and we'll spec the setup.
What is the Audi R8 bolt pattern?
The Audi R8 bolt pattern is 5x112 on both generations, meaning five lugs on a 112 mm circle. The thread is M14x1.5. Our bolt pattern explainer covers how to measure it. Lug seat type (conical or ball) has to match the wheel, not just the car, so new wheels often need different lug bolts than the factory set.
What is the Audi R8 center bore, and why does it differ by generation?
The center bore is the hole in the back of the wheel that locates it on the hub. First-generation R8s use a 57.1 mm hub front and rear. Second-generation cars keep the 57.1 mm front hub but use a larger 66.6 mm rear hub (some fitment databases list it as 66.5 mm). A rear wheel bored for the second-generation hub can go on a first-generation car with hub-centric rings, but a rear wheel bored to 57.1 mm will not fit over a second-generation rear hub at all. See our guide to center bore and hub-centric rings for why this matters for vibration and safety. That's why Variant lists separate R8 fitments for 2009 to 2015 and 2017+ cars, each machined to that car's hub.
What are the factory wheel sizes and offsets on the Audi R8?
Factory sizes are staggered, with a wider rear wheel. Offset (ET) is the distance in millimeters from the wheel's mounting face to its centerline, and a lower number pushes the wheel outward. The table summarizes published factory specs.
| Generation / trim | Front | Rear |
|---|---|---|
| Gen 1 V8 (2008 to 2015) | 18x8.5 ET42, 235/40R18 | 18x10.5 ET50, 285/35R18 |
| Gen 1 V10 / 19-inch option | 19x8.5 ET42, 235/35R19 | 19x11 ET50, 295/30R19 |
| Gen 2 V10 base | 19x8.5 ET42, 245/35R19 | 19x11 ET50, 295/35R19 |
| Gen 2 V10 Plus / Performance | 20x8.5 ET42, 245/30R20 | 20x11 ET50, 305/30R20 |
Should you stay with the factory staggered setup?
For most owners, yes. Staying close to 8.5 inches wide in front and 11 inches wide in the rear keeps the factory tire sizes usable and preserves the car's rear-biased tire footprint. Going wider than stock is possible, but small changes in width or offset move the lip and inner edge quickly, so clearance needs to be verified. If you want to understand the trade-offs, read our guide to staggered vs. square setups. Moving from 19s to 20s is a plus-one change, and the math works because tire sizes like 245/30R20 land within a fraction of a percent of the stock 245/35R19 diameter.
How do you choose an offset that sits flush?
Start from the factory offset, then account for any added width. A wider wheel at the same offset grows equally inward and outward, because offset is measured to the wheel's centerline. Lowering the offset number pushes the whole wheel outward. So if you add width and want the inside edge to stay where it is for suspension and brake clearance, lower the offset by half the width increase; the outer lip then moves out by the full amount of the increase. Our offset guide and flush fitment guide walk through the math.
- Start from the factory wheel width and offset for your generation.
- Decide how far outward you want the lip to sit, measured against the fender.
- If you add width, lower the offset by half the increase to hold the inner edge in place, then verify suspension and brake clearance.
- Check tire width against the approved rim width range published by the tire maker.
Will aftermarket wheels clear R8 brakes?
Usually yes if the wheel is designed for the car, but verify. Ceramic and large steel rotors with big calipers need barrel and spoke clearance that varies by design. Forged wheels can be built with spoke profiles that clear specific calipers. Our guide on checking brake clearance explains how to measure it.
Why choose forged wheels for an R8?
The R8 is a light, mid-engine car, so unsprung weight (the mass not supported by the springs, such as wheels, tires and brakes) matters to ride and response. A true forged wheel in 6061-T6 aluminum can be made strong at low weight. Variant sells only true forged wheels. Our ready-to-order EVO fitments in the Audi R8 collection come in 19x8.5 / 19x11 and 20x9 / 20x11 for first-generation cars, and 20x9 / 20x11 and 20x9 / 21x12 for second-generation cars. You can also browse our vehicle-specific fitments. For tire sizing background, Tire Rack's guide to plus sizing is a reliable reference.
EVO is only one of our lines for the R8. Need a size outside those fitments? Our EVO Custom program builds EVO designs from 17 to 24 inches for your exact car. Prefer a multi-piece wheel? Our EX2 two-piece and three-piece builds, like the Corsa line, are specced to your car one set at a time, so their sizes and offsets can differ from the EVO fitments.
Ready to spec a set? Start with the Audi R8 collection, or tell our fitment experts your year and trim and we'll match the size, offset and hub bore to your car.
Frequently asked questions
Do Gen 1 and Gen 2 Audi R8 wheels interchange?
Not automatically. Both use 5x112 and a 57.1 mm front hub, but the Gen 2 rear hub is larger (66.6 mm) than the Gen 1 rear (57.1 mm). A Gen 2 rear wheel can fit a Gen 1 car with hub-centric rings, but a Gen 1 rear wheel will not fit over a Gen 2 rear hub.
What is the stock wheel size on an Audi R8?
Published factory sizes are 19x8.5 ET42 front and 19x11 ET50 rear on most V10 cars, with 20x8.5 ET42 and 20x11 ET50 on Gen 2 V10 Plus and Performance trims. Early V8 cars used 18x8.5 and 18x10.5.
Can you put 20-inch wheels on a 19-inch Audi R8?
Generally yes. A plus-one change from 19 to 20 inches with a lower-profile tire, such as 245/30R20 in place of 245/35R19, keeps overall diameter within about a quarter of a percent. Confirm brake and fender clearance for your specific wheel.
What bolt pattern does the Audi R8 use?
The Audi R8 uses a 5x112 bolt pattern with M14x1.5 thread. Confirm the lug seat type matches your wheels.
Written by Taylor Smith, co-founder of Variant Alloy Wheels, who has spent nearly two decades in the automotive aftermarket.



Share:
What Wheel Size Should You Run on a Toyota Supra A90? 18 vs. 19 vs. 20 Inch
Do Wheels Affect Tesla Model S Plaid Range? What the EPA Numbers Show