Search By Vehicle

Powered By

Variant Alloy Wheels

The best wheels for the Cadillac CT5-V Blackwing are lightweight forged wheels in a staggered 19-inch setup that respects the factory 5x120 bolt pattern and the car's enormous front brakes. Factory sizing is roughly 19x10 front and 19x11 rear, and 19 inches is effectively the floor because of the Brembo package underneath. On a sedan that weighs about 4,100 pounds and puts 668 horsepower through 305-section rear tires, shaving unsprung weight at each corner is one of the few changes that improves ride, steering response, and braking at the same time.

The CT5-V Blackwing is a strange and wonderful thing: a supercharged V8 super sedan you can still order with a six-speed manual. It is also heavy, fast, and hard on tires, which makes wheel selection more consequential here than on most cars. Our ready-to-order CT5-V Blackwing fitments are forged EVO monoblocks in the factory 19x10 front and 19x11 rear sizes, and EVO is only one of our lines for the car. Here is how to get it right.

What wheels does the CT5-V Blackwing come with from the factory?

Cadillac ships the Blackwing on a staggered 19-inch setup. The commonly listed factory specs are:

Front Rear
Wheel size 19x10 19x11
Tire 275/35ZR19 305/30ZR19
Bolt pattern 5x120

Two things stand out. First, that is a wide stagger, which means you cannot simply reuse specs from a Camaro or a CT4-V Blackwing. Second, the factory wheels are already forged, so a replacement has to match that construction to be worth it. For the full specification sheet, GM Authority publishes the CT5-V Blackwing numbers in detail.

Offset is the single spec most often mis-copied from forum posts, which is why our fitment experts spec it for your car instead of leaving you to guess. If the terminology is fuzzy, start with our guide to wheel offset explained.

What size wheels fit the CT5-V Blackwing?

Staying at or near factory sizing is the safe answer, and for most owners it is also the right one. A 19x10 front and 19x11 rear in the factory offset range fits without fender work, keeps the tire options wide open, and preserves the alignment geometry Cadillac tuned.

Where a custom forged wheel earns its money is in the details around that envelope:

  • Squaring up the offset. Some owners pull the front offset in slightly to fill the arch, which changes scrub radius. Small moves only, and never without checking clearance at full lock.
  • Going a half-inch wider in back. A 19x11.5 can package a 315 on a car with this much rear grip, but it narrows your tire selection considerably.
  • Adjusting the stagger. Because this is a rear-drive car, you have more freedom than an all-wheel-drive platform where front and rear rolling diameters must stay closely matched.

Before committing to a width, check the tire you actually want against its approved rim width range. Tire Rack's reference on rim width and tire size is the clearest public explanation of how the two interact.

Our ready-to-order EVO fitments for the Blackwing stay inside that factory envelope: 19x10 front and 19x11 rear, machined for this car. Want a different width or diameter? Our EVO Custom program builds the same EVO designs from 17 to 24 inches. Browse our CT5-V Blackwing fitments or the rest of our vehicle-specific fitments.

Can you run 20-inch wheels on a CT5-V Blackwing?

It can be done, but understand the trade, and know that Cadillac chose 19s on purpose: the team fit as much tire as it could and kept the sidewall for compliance on track. Going to 20 inches means a shorter sidewall, which sharpens turn-in and looks the part, and costs you ride compliance and pothole protection on a car that already runs a firm suspension. On broken pavement the difference is noticeable.

There is also a weight penalty. A 20-inch wheel and tire package is almost always heavier than the 19-inch equivalent, which works against the main reason to change wheels in the first place. If your car sees track days or rough roads, staying at 19 is the better engineering answer. If it is a show and street car, 20s are defensible. Our ready-to-order EVO fitments for the Blackwing are 19s, and our fitment experts can tell you whether a 20 works for your car through EVO Custom or a multi-piece build. We laid out the general trade-offs in plus sizing explained.

Will aftermarket wheels clear the Blackwing's brakes?

This is the constraint that kills more wheel choices on this car than any other. The CT5-V Blackwing runs six-piston Brembo front calipers over roughly 15.7-inch front rotors, with an optional Brembo carbon-ceramic package. That package is why 19 inches is the practical minimum diameter, and it means spoke shape matters as much as wheel size.

A wheel can be the correct diameter, width, and offset and still foul the caliper if the inner spoke face sits too flat. Before you order, check barrel clearance and spoke profile against the caliper, not just the rotor. Our walkthrough on checking brake clearance covers how to measure it properly. If your car has the carbon-ceramic package, tell us when you order so the design is checked against those calipers.

Does wheel weight actually matter on a car this heavy?

It matters more, not less. Unsprung weight is the mass not supported by the springs: wheels, tires, brakes, and part of the suspension. Every pound removed there is worth several pounds removed from the body, because that mass has to be accelerated, stopped, and controlled by the damper every time the tire meets a bump.

On a 4,100-pound sedan with 668 horsepower, the practical effects show up as quicker damper response over expansion joints, less wheel hop under hard acceleration, and marginally shorter stopping distances from reduced rotational inertia. The factory wheels are already forged, so compare real published weights rather than assuming a big saving. The full explanation is in what is unsprung weight.

To be honest about it: you will not feel a two-pound-per-corner change from the driver's seat on the highway. The gains show up over rough back roads and in the data at a track day.

Staggered or square on the CT5-V Blackwing?

Stay staggered. The Blackwing's chassis balance was developed around a wider rear contact patch, and a square setup on a rear-drive car with this much torque trades away traction for tire-rotation convenience you will rarely use at these widths anyway. Square makes sense on lighter, lower-powered cars; it does not on this one. More on the reasoning in staggered vs. square.

What to look for in a forged wheel for the Blackwing

  1. True forged construction. Pressed 6061-T6 aluminum, not cast or flow-formed. The factory wheels are forged, so anything you replace them with should be too.
  2. A wheel engineered for the weight. This is a heavy sedan, and the wheel has to be designed for its corner weights, especially at 19x11.
  3. Car-specific offset. The offset should be engineered for this car's stagger, not borrowed from the nearest stock option.
  4. Caliper-aware spoke design. Concavity is limited by what has to fit behind it, so the design has to be checked against the Blackwing's calipers.
  5. Monoblock or two-piece. Monoblock for the lightest one-piece construction; a two-piece build when you want a wider lip or a split finish.

Variant sells only forged wheels. For the Blackwing, our CT5-V Blackwing collection holds our ready-to-order EVO monoblock fitments in 19x10 front and 19x11 rear, in six designs and eight finishes. EVO is only one of our lines for this car. Prefer a multi-piece wheel? Our EX2 two-piece and three-piece builds, like the Corsa and Strada lines, are specced to your car one set at a time, so their sizes and offsets won't always match the EVO fitments. Tell our fitment experts about your Blackwing and how you drive it, and we'll spec the right wheel and fitment.

Frequently asked questions

What is the bolt pattern on a Cadillac CT5-V Blackwing?

The CT5-V Blackwing uses a 5x120 bolt pattern, shared with other GM Alpha-platform cars. Variant's EVO fitments for the CT5-V Blackwing are machined to the car's hub bore, so the wheel centers on the hub, not the lug hardware.

What size tires does the CT5-V Blackwing use?

From the factory it runs 275/35ZR19 up front and 305/30ZR19 in the rear, typically on a summer performance tire. If you change wheel widths, re-check the manufacturer's recommended rim width range for whatever tire you plan to run.

How much do the factory CT5-V Blackwing wheels weigh?

Cadillac does not publish a weight for the factory 19-inch forged wheels, and owner-reported figures vary. Because they are already forged, compare the published weight of any replacement against them before you buy.

Do I need new TPMS sensors for aftermarket wheels on a Blackwing?

You will need working sensors in whatever set you are driving on. Many owners move the factory sensors over when running one set, and buy a second set of TPMS sensors if they keep a dedicated track or winter setup mounted.

Can you fit 20-inch wheels on a CT5-V Blackwing?

Brake clearance is not the problem at 20 inches, but fit depends on the exact width, offset and tire, and a 20 adds weight and shortens the sidewall, which firms up an already firm ride. Nineteen inches is what Cadillac chose and what our ready-to-order EVO fitments for the Blackwing use, and it remains the better choice for performance driving and rough roads. If you want 20s, our fitment experts can tell you whether they work for your car through EVO Custom or a multi-piece build.

Written by Taylor Smith, co-founder of Variant Alloy Wheels, who has spent nearly two decades in the automotive aftermarket.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.